Casio AP-460 Instrukcja Użytkownika

PX-760/PX-860/AP-260/AP-460/PX-160MIDI ImplementationCASIO COMPUTER CO., LTD.ContentsI MIDI Message Overview 51 Product Configuration as a MIDI Device

7 Polyphonic Key PressureFormatMessage Format: AnH kkH vvHn: MIDI Channel Numberkk: Key Numbervv: Pressure ValueSend This message is not sent by this

8.2 Modulation (01H)FormatMessage Format: BnH 01H vvHn: MIDI Channel Numbervv: ValueSend This message is not sent by this Instrument.Receive Receipt a

Send Sent when layer balance is adjusted.Receive Receipt changes the volume of the corresponding part.8.6 Pan (0AH)FormatMessage Format: BnH 0AH vvHn:

Send This message is not sent by this Instrument.Receive Receipt change the value of Parameter7 [0-7] (7-Bit Parameter) explained under“20.3 ToneDsp P

– Piano note decay rate– Resonance characteristics and decay rate of Damper Resonance effect resonance notesee“25.2 Damper Pedal Setting Value Table ”i

Receive Receipt performs an operation equivalent to a soft pedal operation.8.13 Vibrato Rate (4CH)FormatMessage Format: BnH 4CH vvHn: MIDI Channel Num

8.16 Portamento Control (54H)FormatMessage Format: BnH 54H vvHn: MIDI Channel Numberkk: Source Note NumberSend This message is not sent by this Instru

8.19 Chorus Send (5DH)FormatMessage Format: BnH 5DH vvHn: MIDI Channel Numbervv: ValueSend This message is sent at initialization, when the panel tone

Send This message is not sent by this Instrument.Receive Receipt changes Pitch Bend Sensitivity.8.21.2 Fine TuneFormatMessage Format: BnH 64H 01H 65H

Send This message is never sent.Receive Receipt deselects RPN.9 Mode Message9.1 All Sound Off (78H)FormatMessage Format: BnH 78H 00Hn: MIDI Channel Num

8.7 Expression (0BH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128.8 General Use Controllers 1 through 8 (10H th

Send Mainly sent in the following cases.• When the keyboard channel is changed• When a recorder function is used• When octave shift changed• When the

9.7 Poly (7FH)FormatMessage Format: BnH 7FH 00Hn: MIDI Channel NumberSend This message is never sent.Receive Receipt of this message stops the current

• Timbre Type: DrumThis Timbre Type is for drum sounds. The method for producing sound is optimized for drums.The damper pedal and sostenuto pedal do

12 Pitch Bend ChangeFormatMessage Format: EnH llH mmHn: MIDI Channel Numberll: Value LSBmm: Value MSBSend This message is not sent by this Instrument.

Part IIISystem Message13 Active SensingFormatMessage Format: FEHSend This message is never sent.Receive Once this message is received, the Active Sens

14.1.2 Master BalanceFormatMessage Format: F0H 7FH 7FH 04H 02H llH mmH F7Hll: Value LSB (Note1)mm: Value MSB (Note1)Note1 : For information about the

Type FormatMessage Format: F0H 7FH 7FH 04H 05H 01H 01H 01H 01H 01H 00H vvH F7Hvv: Value (Note1)Note1 : For information about the relationship between

Send This message is never sent.Receive Receipt changes the System Chorus Rate parameter.Depth FormatMessage Format: F0H 7FH 7FH 04H 05H 01H 01H 01H 0

Receive Receipt returns the sound source to its power on default settings.GM2 System On FormatMessage Format: F0H 7EH 7FH 09H 03H F7HSend This message

Part IVInstrument-Specific System ExclusiveMessages15 FormatThis section explains the format of the Instrument-specific System Exclusive Messages. See“V

IV Instrument-Specific System Exclusive Messages 2915 Format 2915.1 Message Classifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

<- body (Depends on act) ->SX MAN MOD dev act cat mem pset blk prm idx len data EOXIPR Y Y Y Y Y Y Y Y Y Y Y Y - YIPS Y Y Y Y Y Y Y Y Y Y Y Y Y

IPS:Individual Parameter SendIndividual Parameter Send Indicates an individual parameter value send message. When the Instrumentreceives this action,

When there are multiple parameters with the same ID inside the same category, as with the mixerchannel volume setting for example, the block number re

The value of this field specifies the size of the parameter value stored in the data field. Data lengthindicates the length of the array being transferre

A single session is concluded only when this Instrument returns an IPS (Individual Parameter Send)in response to an IPR (Individual Parameter Request)

Part VParameter ListHow to Read the Tables• Number Base Notation“Size”indicates the parameter value bit width as a decimal value. The bitfield position

19 Patch ParametersThe main function of patch parameters is to configure the settings of the sound source of a device.19.1 Master Tune ParametersThese

Note1 : Selects the System Reverb preset type. Receipt of GM/GS Reset selects Standard Hall. This is the value of thisType is also linked to each of t

20 Tone Parameters20.1 Basic ParametersParameter ID R/W Block Size Array Min-Def-Max DescriptionName 0000 R/W 000000 7 10 00-20-7F Ascii CharacterTimb

20.2 LFO ParametersParameter ID R/W Block Size Array Min-Def-Max DescriptionVib Wave 0013 R/W 000000 4 01 00-00-0F 0...Sin1...Tri2...Saw Up3...Saw Dow

24 DSP Parameter Set Types 4124.1 Tremolo/Auto Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4224.2 EQ 3Band . .

21 Music Library ParametersThis parameter is a container for Music Library related information.Parameter ID R/W Block Size Array Min-Def-Max Descripti

Part VIDSP Parameter List22 Tone with DSP ListThis is a list of tones that use DSP.22.1 PX-760,PX-860,AP-260,AP-460,PX-160Tone Number Tone Name Input/

24.1 Tremolo/Auto PanParameter Number Parameter Name Value NotesParameter7[00] Rate 00 - 7FParameter7[01] Depth 00 - 7F24.2 EQ 3BandParameter Number P

24.7 Drive RotaryParameter Number Parameter Name Value NotesParameter7[00] Overdrive Gain 00 - 7FParameter7[01] Overdrive Level 00 - 7FParameter7[02]

Part VIISetting Values and Send/ Receive Values25 Setting Value Tables25.1 Off/On Setting Value TableTransmit Value Receive Value Parameter00H 00H - 3F

25.6 Pan Setting Value TableTransmit/Receive Value Parameter00H Left: :40H Center: :7FH Right25.7 Master Fine Tuning Setting Value TableTransmit Value

PX-760,AP-260,PX-160Transmit/Receive Value Parameter PanelNumber00H Room1 -01H Room2 102H Room3 -03H Hall1 304H Hall2 2(default)05H Plate1 -06H Delay

25.10 Equalizer Frequency Setting Value TableParameter Value Frequency00H 100Hz01H 130Hz02H 160Hz03H 200Hz04H 300Hz05H 400Hz06H 600Hz07H 800Hz08H 1.0K

25.12 DSP Equalizer Gain Setting Value TableParameter Value Gain34H -1235H -1136H -1037H - 938H - 839H - 73AH - 63BH - 53CH - 43DH - 33EH - 23FH - 140

Part VIIIMIDI Implementation Notation26 Value Notation26.1 Hexadecimal NotationMIDI implementation sometimes requires that data be expressed in hexade

Part IMIDI Message Overview1 Product Configuration as a MIDI DeviceAs a MIDI device, the instrument consists of the System Section, Sound Generator Sec

Decimal Hexadecimal Binary0 00H 00000000B1 01H 00000001B2 02H 00000010B3 03H 00000011B4 04H 00000100B5 05H 00000101B6 06H 00000110B7 07H 00000111B8 08

1.2.2 PartsThe settings of the sound generator parts can be changed using Instrument-specific system exclusivemessages. This Instrument consists of 32

as MIDI messages. The channel number of the sent message is in accordance with Instrument ’s partnumb er.1.3.1 Auto Performance MIDI SendThis document

Part IIChannel Message4 Channel Message Overview4.1 Send ChannelFor information about the MIDI channels of the channel messages that are sent when thi

Message Format: 8nH kkH vvH9nH kkH 00H(receive only)n: MIDI Channel Numberkk: Key Numbervv: velocitySend Sent when a key is released.(Note1)The key nu